1 SawStop Contractor Mobile Base
Unpacking Your Mobile Base
Safety
While unpacking your mobile base verify that all the components shown on this page are included.
release lever
3” caster
(two)
3” wheel
(two)
caster support plate
linkage bar
caster support
wheel support
mobile base hardware pack owner’s manual
SawStop
SawStop
®
OWNER’S MANUAL
Contractor Mobile Base
L
ow
er
Raise
Nev
e
r
pl
a
c
e
fi
ng
e
r
s
,
toe
s
or
o
t
h
e
r
bo
d
y
parts
un
der
t
h
e
m
o
bi
l
e
b
a
s
e
.
!
W
A
R
NING
1
.
N
e
v
e
r
p
l
a
c
e
f
i
ng
e
r
s
,
to
e
s
o
r
o
t
h
e
r
b
o
d
y
p
a
r
t
s
u
n
d
e
r
t
h
e
m
o
b
i
l
e
b
a
s
e
.
2
.
A
l
w
a
y
s
us
e
t
h
e
s
a
w
a
n
d
t
h
e
m
o
b
i
l
e
b
a
s
e
on
a
l
e
v
e
l
s
u
r
fac
e
.
3
.
L
o
w
e
r
t
h
e
s
a
w
b
e
f
o
r
e
u
s
s
a
w
w
h
e
n i
t
i
s
r
a
i
s
e
d
o
ff
4
.
L
o
w
e
r
t
h
e
s
a
w
s
l
d
r
op
b
a
c
k
t
o
.
!
W
A
R
NI
N
G
Mobile Base Hardware Pack
Nylon Hex Nuts,
M6 (2)
4
Lock Washers,
M8 x 13.6 (4)
6
Flange Lock Nuts,
M6 (2)
9
Shoulder Socket Screw,
M8 x 17.7 (1)
15
Shoulder Socket Screw,
M8 x 15.7 (1)
13
Nylon Hex Nut,
M8 (1)
19
Cap Nut,
M8 (1)
20
Extension Spring,
(1)
17
Hex Bolts,
M8 x 40 (2)
8
Caster Nuts,
3/8” thread (2)
12
Wave Washer,
M10.5 x 14.5 (1)
16
Short Fixed Wheel Axle,
M6 x 67.6 (1)
1
Long Fixed Wheel Axle,
M6 x 73.8 (1)
2
Washers,
M6 x 16 (4)
3
Button Head Socket
Screws, M8 x 20 (4)
5
Washers,
M8 x 18 (4)
7
Hex Screw,
M8 x 30 (1)
14
Release Lever
Locking Screw (1)
18
Lock Washers,
M10.5 x 17 (2)
11
Washers,
M10.5 x 25 (2)
10
L
ower
R
a
i
s
e
N
e
v
e
r
pla
c
e
f
i
ngers
,
t
oe
s
or
ot
he
r
body
p
a
r
t
s
unde
r
t
h
e
mobi
l
e
ba
s
e
.
!
W
A
R
N
I
N
G
1
.
Ne
v
e
r
pl
a
ce
f
i
n
ger
s
,
t
o
e
s
o
r
o
t
he
r
bo
dy
p
ar
t
s
u
n
de
r
th
e
m
o
bi
le
b
a
s
e
.
2
.
A
lw
a
y
s
us
e
t
h
e
s
a
w
a
nd
t
h
e
m
obi
l
e
b
a
s
e
on
a
le
v
e
l
s
u
r
f
a
c
e.
3
.
Lo
w
e
r
t
h
e
s
a
w
before
usi
ng
sa
w
w
h
e
n
it i
s
r
ais
ed
o
ff
4
.
Lo
w
e
r
t
h
e
s
aw
s
lo
d
r
op
b
a
c
k
to
.
!
W
A
R
NI
NG
1. Never place ngers, toes or other body parts under the saw when it is raised onto the mobile base. The base
may suddenly lower on you and cause a severe injury.
2. Do not attempt to use or move the saw on an inclined surface. The weight of the saw makes it difcult to stop on
an inclined surface. Attempting to use or move the saw on an inclined surface could result in a severe injury.
3. Make sure the saw is fully lowered to the ground and stable before operating the saw. Otherwise, the saw could
move unexpectedly and cause a severe injury.
4. Be sure to unplug or disconnect the saw from power before moving or repositioning it. The main power cord or
the power outlet could be damaged if the saw is not disconnected from power before moving it.
Note: If you are using the SawStop Out-Feed Table you must remove it before moving your saw with the Contractor
Saw Mobile Base. Attempting to lift the saw with the out-feed table attached may damage the out-feed table.
(4 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji